
Say two compact sedans come in on the same morning, one gas and one battery-electric, each with a pushed-in front fender, a cracked headlamp and a scraped lower door. Once the gas car has had its pre-repair scan, it can be taken apart and its parts list written. On the EV, the maker's procedure for that area calls for the high-voltage system to be shut down first, and the battery gets checked before anyone touches the fender. An EV repair follows a fixed order set by its maker, and several of its steps can't start until the one before them is done.
Industry figures show EV repairs taking longer overall. Mitchell's collision data for Canada put the average battery-electric repair at 17.2 days from keys in to keys out in 2024, through the third quarter, against 14.3 days for a gas car. Mitchell's Ryan Mandell points to the extra diagnostic and calibration work damaged EVs need, which can add cost, complexity and cycle time to each repair. The work keeps growing, too. Mitchell put battery-electric vehicles at 4.77 per cent of repairable collision claims in Canada in 2025, up 24 per cent in a year, and its first-quarter 2026 report, released in May, had them at 4.94 per cent. By the second quarter, battery-electric vehicles had reached a record 5.42 per cent of repairable claims in Canada, and mild hybrids 5.52 per cent.
Why does the high-voltage work come first?
On an EV, two things usually happen before anyone pulls a bumper cover. The first is a pre-repair scan. I-CAR defines it as part of damage analysis, the stage the trade calls blueprinting, used to find faults related and unrelated to the collision and to capture diagnostic trouble codes. It can't be done once the 12-volt system and the car's communication networks are disabled, so it comes before any shutdown. When the damage rules it out at the start, I-CAR says it should be done as soon as the repair allows it to be done safely.
The second is the high-voltage disable, when the maker's procedure calls for one. The system is shut down and confirmed with a meter to be de-energized, following that procedure, before anyone works near the battery, the high-voltage cables or the components they feed. I-CAR's guidance says only qualified high-voltage technicians wearing proper protective equipment work on that system. Its best-practice protocol uses a form to document each inspection and test, along with printable status cards that show the current state of the car. Tesla's own procedure tells technicians to assume high voltage is present until a multimeter proves otherwise, and to check both sides of a high-voltage connector every time one is disconnected.
Makers don't all write this step the same way. I-CAR notes that disable instructions can change from vehicle to vehicle depending on the year, and that some call for a scan tool while others need a high-voltage meter. On a Porsche, I-CAR's guide to Porsche high-voltage tools says both may be required.
Then comes the wait. Switching the system off doesn't drain everything at once, because the inverter holds a charge in its capacitor. Toyota's guidance, as reported by the U.S. trade outlet Repairer Driven News in 2022, treats every high-voltage battery as unstable after a crash, and once the system is switched off and the service plug grip is removed, it calls for a wait of at least 10 minutes for the capacitor inside the inverter to discharge. It is a short wait, and no work near the high-voltage parts starts until it is over. A gas car has no equivalent step.
What does the battery check decide?
With the system safe, the battery and its mounts are assessed against the manufacturer's procedure, and a hit low on the body gets extra attention. Tesla's procedure for preparing a total-loss Model Y for transport, for example, sends technicians to a separate underside inspection if the high-voltage battery shows any damage, and to Tesla Collision Repair if battery damage is found or suspected.
Whatever the check finds sets the scope of the job. A pack that passes means the repair carries on around it. A pack that has to come out adds handling, parts and time. In the worst case, battery damage can make the car a total loss, and our post on total losses for luxury cars and EVs explains how that decision gets made.
Where does a car with a damaged pack wait?
A suspect battery can also change where the car sits. Volvo's position, published through I-CAR, says that when repair work can't start right away, a damaged high-voltage vehicle should be positioned in a fire-protected area outdoors, with a 15-metre safety distance between the vehicle and anything combustible. The car is cordoned off with a warning sign. Other makers publish their own rules for this.
Why does the parts order carry so much weight?
EV estimates lean hard on the maker's own parts. In Mitchell's second-quarter 2026 report, 84.74 per cent of parts on battery-electric repair estimates were original manufacturer parts, compared with 61.44 per cent for gas vehicles. Battery-electric cars also had fewer damaged parts slated for repair instead of replacement, 14.81 per cent against 16.6 per cent. CCC's 2026 review of the U.S. market found the same pattern, with EV repairs relying heavily on manufacturer parts and limited aftermarket availability compared with gas cars.
With fewer places to get a part, the list has to be right the first time, and it can only be right once the car is apart. At CSN Avenue we carefully disassemble the car so no damage is missed, and that teardown is what lets us write a detailed estimate of the work and costs. For Tesla owners, our partnership with Tesla means quicker service times and access to genuine manufacturer parts.
A part on back order holds up its own step and everything behind it. A quarter panel can't be sealed and painted around a missing bracket, and the sensors in a bumper can't be calibrated before it is on the car.
What changes in the structural repair?
Once the parts are known, the body work starts, and the maker's procedure still sets the rules. Tesla's structural repair procedures say not to weld on a Tesla before the Vehicle HV Disablement Procedure is done, and that only technicians who have completed Tesla's approved welding training may weld structural components.
Heat near the pack is controlled as well. Where adhesive is force-cured close to the high-voltage battery, Tesla's Model X repair procedure, for one, says the battery must not go above 74 degrees Celsius, warning that heating it past that for an extended period could hurt people or damage the battery. Adhesive sets the pace in a less obvious way, too. If a repair calls for resistance spot welds alongside adhesive, the method the trade calls weld bonding, Tesla says the welding has to be finished before the adhesive cures, so the welding time gets planned into the job before anything is glued.
Corrosion protection runs through the rest of the job. Tesla's post-repair operations call for an anti-corrosion coating on bare metal after a structural repair, cavity wax or a similar coating inside body cavities once the car is refinished, and seam sealer on all seams and folded hems, because Tesla's service parts arrive without factory seam sealer. Wiring that moved during the repair is checked so clips and connectors fasten securely and harnesses keep their clearance from moving parts.
The downtown shop has Tesla-specific tools for aluminum bodywork and advanced electronics, a Car-O-Liner system for measuring structure, and tools and equipment approved by the vehicle manufacturer. The metal itself gets its own write-up in aluminum and mixed-material repairs.
What sets the bake limits on an EV?
Fresh paint is usually force-dried in a heated booth, and on an EV the battery goes into that booth with the panels. Tesla allows baking with the high-voltage battery installed inside set limits. The bake runs no longer than 45 minutes, the car starts below 35 degrees Celsius, and the battery stays at or under 60 degrees. If the battery temperature can't be determined, the car has to sit somewhere below 35 degrees for at least 12 hours before the bake starts. If repairs to the cooling or climate system aren't finished, high and low voltage power are disconnected so those systems can't switch on during the bake. Anything outside those limits goes to Tesla Collision Repair before the work continues.
Other makers draw the line in different places. For the 2021 MINI Cooper Electric SE, the instruction I-CAR quotes allows a maximum of 2 hours in the dryer at an object temperature of 60 degrees. Two I-CAR subject matter experts, writing in FenderBender in March 2026, add that some makers allow no baking at all, and that these details can change from month to month and vary by model, so the procedure is checked before every bake. One booth routine for every car would break somebody's rule, so each bake is planned from that car's own procedure.
Tesla also does not approve clear coat blending in collision repair. Its preferred process blends the base colour as needed and then applies clear coat to the entire panel, edge to edge. That can put more panel area in the booth than the damage alone would suggest. CSN Avenue paints in two downdraft spray booths and matches colour with the AkzoNobel Automatchic tool.
What has to wait until the car is back together?
Calibrations measure the finished car, so they have to wait for it. I-CAR's definition of post-repair calibration says it is required after the removal, installation or repair of many safety and driver convenience parts, and it may also be needed when the mounting locations were damaged, or when parts in front of or behind cameras and sensors are removed. Access to the maker's information is mandatory to decide whether a calibration is required. A sensor calibrated on a bumper that later comes off for paint would need the work done again, so calibration waits until body, paint and reassembly are complete. The wheels come into it as well. When I-CAR asked one maker whether a wheel alignment is needed before calibration, the answer was that it depends on the work done, but either way the thrust angle, the line the rear wheels set for the car, has to be true before the calibration.
EVs carry more of this work than other cars. Mitchell's 2025 year-in-review, which doesn't break this figure out by country, had battery-electric vehicles averaging 1.70 calibrations per estimate, against 1.54 for gas cars. CCC's 2026 review of the U.S. market points to the heavy concentration of sensors, cameras and other safety features in areas that get hit often, such as bumpers and doors.
The last look at the car follows the calibrations. Unplugging lamps and sensors during a repair can set fault codes, and the post-repair scan is where codes from the collision and from the repair are identified and cleared. At CSN Avenue, the final inspection tests all systems, including electronic and safety features, before the car is delivered back to you. Software updates can be part of that last stage as well.
Why can't the order be reshuffled?
Go back to the illustrative EV from the opening. The pre-repair scan captures its codes while it has power. Its maker's procedure calls for a shutdown, so the high-voltage system is disabled, verified and marked with its status. With the hit low on the front corner, the pack and its mounts get a careful look. Once the pack is cleared, the car comes apart and the parts list is written from what the teardown found. The fender is replaced, the door is repaired, and the bare metal is sealed and protected. The refinished panels go through a bake that stays inside the maker's battery limits, the car is reassembled with its new headlamp, and any camera or sensor the repair affected is calibrated before the final checks.
Each step sits where it does because of the one before it. Calibrating before reassembly means parts come back off and the calibration happens twice. A parts list written before teardown tends to miss the bracket hiding behind the headlamp, and that bracket becomes a second order with its own wait. Welding before the disable breaks the maker's procedure outright, and a final scan run before reassembly can't check modules that aren't plugged back in yet. A delay early in the sequence pushes back every step after it, so the battery result and the teardown can move the finish date.
What does CSN Avenue bring to the work?
CSN Avenue is a Tesla Approved Body Shop in downtown Toronto. Our shop at 293 Macpherson Avenue has 21,000 square feet of production space, equipped with Tesla-specific tools, and our team continually takes part in training programs directly from luxury vehicle manufacturers. We hold manufacturer certifications from makers including Tesla, Porsche, BMW, MINI, Toyota and Lexus, and our facility has the booths, measuring system and equipment behind the work.
Our process starts with an inspection using diagnostic tools to find visible and underlying damage, followed by careful disassembly. The estimate sets out the costs and the time frame for the repair. As a preferred insurance partner, we can handle the paperwork and communicate with your insurance provider directly if needed.
Does the same order apply to a BMW, MINI, Porsche or Lexus?
The broad sequence holds across makes, and the details inside each step change with the badge. Porsche's disable may need a scan tool as well as a high-voltage meter, Toyota sets its own capacitor wait, and the MINI bake limit above is a different rule from Tesla's. You'll find every brand we're certified for on our certifications page, and our guides to BMW and MINI repair, Porsche repair and Lexus and Toyota repair cover each brand. For the general stages of any repair, see our estimate to delivery post.
Questions about EV repair timing
Why can't you give a firm finish date on the first day?
Two of the biggest unknowns, the battery result and the teardown, are still ahead on day one. Until those are done, nobody knows whether the pack stays, which parts the car needs or which calibrations the repair will call for. Once they are done, the estimate sets out the costs and the time frame. Our post on whether you'll be without your car covers what drives repair time in general.
Does a light scuff on an EV need the high-voltage steps?
The high-voltage steps depend on where the damage is and what the maker's procedure calls for, so a light scuff well away from high-voltage parts may need less of that work. A final scan still applies, and calibration can too. Bumpers on newer cars carry radar and parking sensors, and under I-CAR's definition, removing parts in front of or behind sensors can be enough to require a calibration.
Is a hybrid on the same clock?
Some of it carries over. Full and plug-in hybrids have high-voltage systems, so the maker's disable steps can apply, and Mitchell's 2024 data found average repair times for mild and plug-in hybrids also ran longer than for gas cars in both Canada and the U.S. Mild hybrids reached 5.28 per cent of repairable claims in Canada in the first quarter of 2026.
Is a Tesla handled any differently?
Tesla follows the same broad sequence and writes its own rules for every step, from the disable and welding procedures to the bake limits and the battery inspections. Our Tesla partnership means quicker service times, access to genuine manufacturer parts and repairs that strictly follow the manufacturer's specifications. Our Tesla downtown post covers Tesla repairs in more depth.
Why scan an EV when nothing is lit on the dash?
A dark dashboard doesn't mean a clean system. I-CAR describes the pre-repair scan as a way to identify errors, faults and damage both related and unrelated to the collision, and to capture the trouble codes stored in the car. It also has to happen while the 12-volt system and networks are still running, which is one more reason it sits at the very front of an EV repair.
If your EV has been in a collision, bring it to a shop that plans for every step of that order from day one. Book your EV estimate online or call us at 416-923-8031, Monday to Friday from 7:30 a.m. to 5:00 p.m. We're at 293 Macpherson Avenue, and if the car shouldn't be driven, one of our damage appraisers can come to you for a mobile estimate.

















